Fault Recording Register Low [0] (FRCDL_REG_0_0_0_VTDBAR) – Offset 400 - 1.3 - ID:767626 | 12th Generation Intel® Core™ Processor Datasheet Volume 2 of 2

Introduction
Processor Configuration Register Definitions and Address Ranges
D0:F0 Host Bridge and DRAM Controller - DMIBAR Registers
D0:F0 Host Bridge and DRAM Controller - GFXVTBAR Registers
D0:F0 Host Bridge and DRAM Controller - GTTMMADR Registers (part 1)
D0:F0 Host Bridge and DRAM Controller - GTTMMADR Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - Host Bridge/DRAM Registers (part 1)
- Revision ID (RID_0_0_0_PCI)
D0:F0 Host Bridge and DRAM Controller - Host Bridge/DRAM Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Host Controller Registers (part 1)
- GFX VT Range Base Address Register (GFXVTBAR_0_0_0_MCHBAR_NCU)
- VT DMI PEG VC0 Range Base Address Register (VTDPVC0BAR_0_0_0_MCHBAR_NCU)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Host Controller Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 3)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 4)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 5)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Power Management Registers (part 1)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Power Management Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - PXPEPBAR PCI Express Egress Port Registers
D0:F0 Host Bridge and DRAM Controller - VTDPVC0BAR Registers
D1:F0-1 PCI Express* Controller Registers
D10:F0 Platform Monitoring Technology (PMT) Registers
D14:F0 Volume Management Device
D14:F0 Volume Management Device MEMBAR2 Registers
D2:F0 Processor Graphics
D4:F0 Dynamic Tuning Technology Registers
D6:F0 PCI Express* Controller Registers
D8:F0 Gauss Newton Algorithm Registers

Fault Recording Register Low [0] (FRCDL_REG_0_0_0_VTDBAR) – Offset 400

Register to record fault information when primary fault logging is active. Hardware reports the number and location of fault recording registers through the Capability register. This register is relevant only for primary fault logging

This register is sticky and can be cleared only through power good reset or by software clearing the RW1C fields by writing a 1.

Bit Range	Default	Access	Field Name and Description
63:12	0x0	RO/V	Fault Info (FI) When the Fault Reason (FR) field indicates one of the address translation fault conditions, bits 63:12 of this field contains the page address in the faulted request. When PASID Present field is 0 (i.e, faulted request is a request without PASID), hardware treat bits 63:N as reserved (0), where N is the maximum guest address width (MGAW) supported. For requests-withPASID (PASID Present field = 1), hardware treats bits 63:N as reserved (0), where N corresponds to the largest AGAW value supported by hardware. When the Fault Reason (FR) field indicates interrupt-remapping fault conditions other than Fault Reason 25h, bits 63:48 of this field indicate the interrupt_index computed for the faulted interrupt request, and bits 47:12 are cleared. When the Fault Reason (FR) field indicates interrupt-remapping fault condition of blocked Compatibility mode interrupt (Fault Reason 25h), contents of this field is undefined. This field is relevant only when the F field is Set.
11:0	0h	RO	Reserved

Bit Range

Default

Access

Field Name and Description

63:12

0x0

RO/V

Fault Info (FI)

When the Fault Reason (FR) field indicates one of the address translation fault conditions, bits 63:12 of this field contains the page address in the faulted request. When PASID Present field is 0 (i.e, faulted request is a request without PASID), hardware treat bits 63:N as reserved (0), where N is the maximum guest address width (MGAW) supported. For requests-withPASID (PASID Present field = 1), hardware treats bits 63:N as reserved (0), where N corresponds to the largest AGAW value supported by hardware.

When the Fault Reason (FR) field indicates interrupt-remapping fault conditions other than Fault Reason 25h, bits 63:48 of this field indicate the interrupt_index computed for the faulted interrupt request, and bits 47:12 are cleared. When the Fault Reason (FR) field indicates interrupt-remapping fault condition of blocked Compatibility mode interrupt (Fault Reason 25h), contents of this field is undefined.

This field is relevant only when the F field is Set.

11:0

Reserved

Fault Recording Register High [0] (FRCDH_REG_0_0_0_VTDBAR)

Variable-Range MTRR Format Physical Mask 9 (MTRR_PHYSMASK9_REG_0_0_0_VTDBAR) Fault Recording Register High [0] (FRCDH_REG_0_0_0_VTDBAR)