Invalidation Event Control Register (IECTL_REG_0_0_0_VTDBAR) – Offset A0 - 1.3 - ID:767626 | 12th Generation Intel® Core™ Processor Datasheet Volume 2 of 2

Introduction
Processor Configuration Register Definitions and Address Ranges
D0:F0 Host Bridge and DRAM Controller - DMIBAR Registers
D0:F0 Host Bridge and DRAM Controller - GFXVTBAR Registers
D0:F0 Host Bridge and DRAM Controller - GTTMMADR Registers (part 1)
D0:F0 Host Bridge and DRAM Controller - GTTMMADR Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - Host Bridge/DRAM Registers (part 1)
- Revision ID (RID_0_0_0_PCI)
D0:F0 Host Bridge and DRAM Controller - Host Bridge/DRAM Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Host Controller Registers (part 1)
- GFX VT Range Base Address Register (GFXVTBAR_0_0_0_MCHBAR_NCU)
- VT DMI PEG VC0 Range Base Address Register (VTDPVC0BAR_0_0_0_MCHBAR_NCU)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Host Controller Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 3)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 4)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Memory Controller Registers (part 5)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Power Management Registers (part 1)
D0:F0 Host Bridge and DRAM Controller - MCHBAR Power Management Registers (part 2)
D0:F0 Host Bridge and DRAM Controller - PXPEPBAR PCI Express Egress Port Registers
D0:F0 Host Bridge and DRAM Controller - VTDPVC0BAR Registers
D1:F0-1 PCI Express* Controller Registers
D10:F0 Platform Monitoring Technology (PMT) Registers
D14:F0 Volume Management Device
D14:F0 Volume Management Device MEMBAR2 Registers
D2:F0 Processor Graphics
D4:F0 Dynamic Tuning Technology Registers
D6:F0 PCI Express* Controller Registers
D8:F0 Gauss Newton Algorithm Registers

Invalidation Event Control Register (IECTL_REG_0_0_0_VTDBAR) – Offset A0

This register is treated as RsvdZ by implementations reporting Queued Invalidation (QI) as not supported in the Extended Capability register.

Bit Range	Default	Access	Field Name and Description
31	0x1	RW	Interrupt Mask (IM) 0: No masking of interrupt. When a invalidation event condition is detected, hardware issues an interrupt message (using the Invalidation Event Data & Invalidation Event Address register values). 1: This is the value on reset. Software may mask interrupt message generation by setting this field. Hardware is prohibited from sending the interrupt message when this field is Set.
30	0x0	RO/V	Interrupt Pending (IP) Hardware sets the IP field whenever it detects an interrupt condition. Interrupt condition is defined as: An Invalidation Wait Descriptor with Interrupt Flag (IF) field Set completed, setting the IWC field in the Invalidation Completion Status register If the IWC field in the Invalidation Completion Status register was already Set at the time of setting this field, it is not treated as a new interrupt condition The IP field is kept Set by hardware while the interrupt message is held pending. The interrupt message could be held pending due to interrupt mask (IM field) being Set, or due to other transient hardware conditions. The IP field is cleared by hardware as soon as the interrupt message pending condition is serviced. This could be due to either: 0: Hardware issuing the interrupt message due to either change in the transient hardware condition that caused interrupt message to be held pending or due to software clearing the IM field. 1: Software servicing the IWC field in the Invalidation Completion Status register.
29:0	0h	RO	Reserved

Bit Range

Default

Access

Field Name and Description

0x1

Interrupt Mask (IM)

0: No masking of interrupt. When a invalidation event condition is detected, hardware issues an interrupt message (using the Invalidation Event Data & Invalidation Event Address register values).
1: This is the value on reset. Software may mask interrupt message generation by setting this field. Hardware is prohibited from sending the interrupt message when this field is Set.

0x0

RO/V

Interrupt Pending (IP)

Hardware sets the IP field whenever it detects an interrupt condition. Interrupt condition is defined as:
An Invalidation Wait Descriptor with Interrupt Flag (IF) field Set completed, setting the IWC field in the Invalidation Completion Status register
If the IWC field in the Invalidation Completion Status register was already Set at the time of setting this field, it is not treated as a new interrupt condition
The IP field is kept Set by hardware while the interrupt message is held pending. The interrupt message could be held pending due to interrupt mask (IM field) being Set, or due to other transient hardware conditions. The IP field is cleared by hardware as soon as the interrupt message pending condition is serviced. This could be due to either:
0: Hardware issuing the interrupt message due to either change in the transient hardware condition that caused interrupt message to be held pending or due to software clearing the IM field.
1: Software servicing the IWC field in the Invalidation Completion Status register.

29:0

Reserved

Invalidation Event Data Register (IEDATA_REG_0_0_0_VTDBAR)

Invalidation Completion Status Register (ICS_REG_0_0_0_VTDBAR) Invalidation Event Data Register (IEDATA_REG_0_0_0_VTDBAR)