7

0b

RW

(HEN)

This field enables a memory hole in DRAM space. The DRAM that lies behind this space is not remapped.
0: No memory hole.
1: Memory hole from 15MB to 16MB.
This bit is Intel TXT lockable.

6:5

0h

RO

Reserved

4

1b

RW

(MDAPCIe)

This bit works with the VGA Enable bits in the BCTRL register of Non PEG devices to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should be set to 1 by default.
It is assumed that these devices will not need to support legacy MDA graphics. However this single bit is added just to support this rare case of using MDA over these devices.
The behavior of this bit field is identical to bits [3:0]

3

0b

RW

(MDAP60)

This bit works with the VGA Enable bits in the BCTRL register of Device 1 Function 2 to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should not be set if device 1 function 2 VGA Enable bit is not set.
If device 1 function 2 VGA enable bit is not set, then accesses to IO address range x3BCh-x3BFh remain on the backbone.
If the VGA enable bit is set and MDA is not present, then accesses to IO address range x3BCh-x3BFh are forwarded to PCI Express through device 1 function 2 if the address is within the corresponding IOBASE and IOLIMIT, otherwise they remain on the backbone.
MDA resources are defined as the following:
Memory: 0B0000h - 0B7FFFh
I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh,
(including ISA address aliases, A[15:10] are not used in decode)
Any I/O reference that includes the I/O locations listed above, or their aliases, will remain on the backbone even if the reference also includes I/O locations not listed above.
The following table shows the behavior for all combinations of MDA and VGA:
VGAEN MDAP Description
0 0 All References to MDA and VGA space are not claimed by Device 1 Function 2.
0 1 Illegal combination
1 0 All VGA and MDA references are routed to PCI Express Graphics Attach device 1 function 2.
1 1 All VGA references are routed to PCI Express Graphics Attach device 1 function 2. MDA references are not claimed by device 1 function 2.
VGA and MDA memory cycles can only be routed across PEG12 when MAE (PCICMD12[1]) is set. VGA and MDA I/O cycles can only be routed across PEG12 if IOAE (PCICMD12[0]) is set.

2

0b

RW

(MDAP12)

This bit works with the VGA Enable bits in the BCTRL register of Device 1 Function 2 to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should not be set if device 1 function 2 VGA Enable bit is not set.
If device 1 function 2 VGA enable bit is not set, then accesses to IO address range x3BCh-x3BFh remain on the backbone.
If the VGA enable bit is set and MDA is not present, then accesses to IO address range x3BCh-x3BFh are forwarded to PCI Express through device 1 function 2 if the address is within the corresponding IOBASE and IOLIMIT, otherwise they remain on the backbone.
MDA resources are defined as the following:
Memory: 0B0000h - 0B7FFFh
I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh,
(including ISA address aliases, A[15:10] are not used in decode)
Any I/O reference that includes the I/O locations listed above, or their aliases, will remain on the backbone even if the reference also includes I/O locations not listed above.
The following table shows the behavior for all combinations of MDA and VGA:
VGAEN MDAP Description
0 0 All References to MDA and VGA space are not claimed by Device 1 Function 2.
0 1 Illegal combination
1 0 All VGA and MDA references are routed to PCI Express Graphics Attach device 1 function 2.
1 1 All VGA references are routed to PCI Express Graphics Attach device 1 function 2. MDA references are not claimed by device 1 function 2.
VGA and MDA memory cycles can only be routed across PEG12 when MAE (PCICMD12[1]) is set. VGA and MDA I/O cycles can only be routed across PEG12 if IOAE (PCICMD12[0]) is set.

1

0b

RW

(MDAP11)

This bit works with the VGA Enable bits in the BCTRL register of Device 1 Function 1 to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should not be set if device 1 function 1 VGA Enable bit is not set.
If device 1 function 1 VGA enable bit is not set, then accesses to IO address range x3BCh-x3BFh remain on the backbone.
If the VGA enable bit is set and MDA is not present, then accesses to IO address range x3BCh-x3BFh are forwarded to PCI Express through device 1 function 1 if the address is within the corresponding IOBASE and IOLIMIT, otherwise they remain on the backbone.
MDA resources are defined as the following:
Memory: 0B0000h - 0B7FFFh
I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh,
(including ISA address aliases, A[15:10] are not used in decode)
Any I/O reference that includes the I/O locations listed above, or their aliases, will remain on the backbone even if the reference also includes I/O locations not listed above.
The following table shows the behavior for all combinations of MDA and VGA:
VGAEN MDAP Description
0 0 All References to MDA and VGA space are not claimed by Device 1 Function 1.
0 1 Illegal combination
1 0 All VGA and MDA references are routed to PCI Express Graphics Attach device 1 function 1.
1 1 All VGA references are routed to PCI Express Graphics Attach device 1 function 1. MDA references are not claimed by device 1 function 1.
VGA and MDA memory cycles can only be routed across PEG11 when MAE (PCICMD11[1]) is set. VGA and MDA I/O cycles can only be routed across PEG11 if IOAE (PCICMD11[0]) is set.

0

0b

RW

(MDAP10)

This bit works with the VGA Enable bits in the BCTRL register of Device 1 Function 0 to control the routing of CPU initiated transactions targeting MDA compatible I/O and memory address ranges. This bit should not be set if device 1 function 0 VGA Enable bit is not set.
If device 1 function 0 VGA enable bit is not set, then accesses to IO address range x3BCh-x3BFh remain on the backbone.
If the VGA enable bit is set and MDA is not present, then accesses to IO address range x3BCh-x3BFh are forwarded to PCI Express through device 1 function 0 if the address is within the corresponding IOBASE and IOLIMIT, otherwise they remain on the backbone.
MDA resources are defined as the following:
Memory: 0B0000h - 0B7FFFh
I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh,
(including ISA address aliases, A[15:10] are not used in decode)
Any I/O reference that includes the I/O locations listed above, or their aliases, will remain on the backbone even if the reference also includes I/O locations not listed above.
The following table shows the behavior for all combinations of MDA and VGA:
VGAEN MDAP Description
0 0 All References to MDA and VGA space are not claimed by Device 1 Function 0.
0 1 Illegal combination
1 0 All VGA and MDA references are routed to PCI Express Graphics Attach device 1 function 0.
1 1 All VGA references are routed to PCI Express Graphics Attach device 1 function 0. MDA references are not claimed by device 1 function 0.
VGA and MDA memory cycles can only be routed across PEG10 when MAE (PCICMD10[1]) is set. VGA and MDA I/O cycles can only be routed across PEG10 if IOAE (PCICMD10[0]) is set.