31

0h

RW

Flash SPI SMI# Enable (FSMIE)

When set to 1, the SPI asserts an SMI# request whenever the Flash Cycle Done bit is 1.

30

0h

RO/V

START RPMC (SRPMC)

When set to 1 by HW, indicate current master is owning the RPMC OP1 and OP2.

29:24

0h

RW

Flash Data Byte Count (FDBC)

This field specifies the number of bytes to shift in or out during the data portion of the SPI cycle. The contents of this register are 0s based with 0b representing 1 byte and 3Fh representing 64 bytes. The number of bytes transferred is the value of this field plus 1. This field is ignored for the Block Erase command.

23:22

0h

RO

Reserved

21

0h

RW

Write Enable Type (WET)

0: Use 06h as the write enable instruction
1: Use 50h as the write enable instruction
Note: No supported flash devices require the 50h opcode to enable a non-volatile status register write. This bit is no longer required.

20:17

0h

RW

Flash Cycle (FCYCLE)

This field defines the Flash SPI cycle type generated to the FLASH when the FGO bit is set as defined below:
0h: Read (1 up to 64 bytes by setting FDBC)
1h: Reserved
2h: Write (1 up to 64 bytes by setting FDBC)
3h: 4k Block Erase
4h: 64k Sector erase
5h: Read SFDP
6h: Read JEDEC ID
7h: write status
8h: read status
9h: RPMC OP1
Ah: RPMC OP2
Bh - Fh: Reserved
Flash controller hardware automatically inserts a write enable opcode prior to Write and erase operations. Hardware automatically polls for device not-busy using read status after write and erase operations.
If the device does not support 64k erase size (or if it doesn't support SFDP) then only 4k is allowed.
Note: If reserved '1' is programmed to this field, flash controller will handle it as if it is 0 (Read) (Preserves legacy behavior.) Other reserved operations, set the FCERR bit and do not issue a cycle on the SPI bus.

16

0h

RW/1S/V

Flash Cycle Go (FGO)

A write to this register with a '1' in this bit initiates a request to the Flash SPI Arbiter to start a cycle. This register is cleared by hardware when the cycle is granted by the SPI arbiter to run the cycle on the SPI bus. When the cycle is complete, the FDONE bit is set.
Software is forbidden to write to any register in the HSFLCTL register between the FGO bit getting set and the FDONE bit being cleared. Any attempt to violate this rule will be ignored by hardware.
Hardware allows other bits in this register to be programmed for the same transaction when writing this bit to 1. This saves an additional memory write. This bit remains set until the transaction is granted by the SPI Controller's internal arbiter.

15

0h

RW/L

Flash Configuration Lock-Down (FLOCKDN)

When set to 1, those Flash Program Registers that are locked down by this FLOCKDN bit cannot be written. Once set to 1, this bit can only be cleared by a hardware reset.

14

0h

RO/V

Flash Descriptor Valid (FDV)

This bit is set to a 1 if the Flash Controller read the correct Flash Descriptor Signature. If the Flash Descriptor Valid bit is not 1, software cannot use the Hardware Sequencing registers, but must use the software sequencing registers. Any attempt to use the Hardware Sequencing registers will result in the FCERR bit being set.

13

1h

RO/V

Flash Descriptor Override Pin-Strap Status (FDOPSS)

This register indicates whether the flash controller is overriding descriptor permissions due to the Pin-Strap. Note: the register value is the inversion of the level sampled on the external pinstrap.
1: No override
0: The Flash Descriptor Overide strap is set

12

0h

RW/L

PRR3 PRR4 Lock-Down (PRR34_​LOCKDN)

When set to 1, the BIOS PRR3 and PRR4 registers cannot be written. Once set to 1, this bit can only be cleared by a hardware reset.

11

0h

RW/L

Write Status Disable (WRSDIS)

0: Write status operation may be issued using Hardware Sequencing.
1: Write status is not allowed as a Hardware Sequencing operation. The flash controller will block the operation and set the FCERR bit when software sets the 'go' bit.

10:6

0h

RO

Reserved

5

0h

RO/V

SPI Cycle In Progress (H_​SCIP)

Hardware sets this bit when software sets the Flash Cycle Go (FGO) bit in the Hardware Sequencing Flash Control register. This bit remains set until the cycle completes on the SPI interface or the transaction is prevented due to any protection policy violation (descriptor, address range, protected region, etc). Hardware automatically sets and clears this bit so that software can determine when read data is valid and/or when it is safe to begin programming the next command. Software must only program the next command when this bit is 0.

4:3

0h

RO

Reserved

2

0h

RW/1C/V

Access Error Log (H_​AEL)

Hardware sets this bit to a 1 when an attempt was made to access the BIOS region using the direct access method or an access to the BIOS Program Registers that violated the security restrictions. This bit is simply a log of an access security violation. This bit is cleared by software writing a '1'.

1

0h

RW/1C/V

Flash Cycle Error (FCERR)

Hardware sets this bit to 1 when a program register access is blocked to the FLASH due to one of the protection policies or when any of the programmed cycle registers is written while a programmed access is already in progress. This bit remains asserted until cleared by software writing a 1 or until a partition reset occurs. Software must clear this bit before setting the FLASH Cycle GO bit in this register.

0

0h

RW/1C/V

Flash Cycle Done (FDONE)

This bit is set to 1 when the SPI Cycle completes after software previously set the FGO bit. This bit remains asserted until cleared by software writing a 1 or partition reset. When this bit is set and the SPI SMI Enable bit is set the flash controller sends SMI messages. Software must make sure this bit is cleared prior to enabling the SPI SMI assertion for a new programmed access.