AUX Power Management Control (AUX_CTRL_REG1) – Offset 80E0 - 1.3 - ID:764981 | 13th Generation Intel® Core™ Processor Datasheet, Volume 2 of 2

13th Generation Intel® Core™ Processor Datasheet, Volume 2 of 2

ID	Date	Version	Classification
764981	07/13/2023		Public

AUX Power Management Control (AUX_CTRL_REG1) – Offset 80E0

AUX Power Management Control

Bit Range	Default	Access	Field Name and Description
31	0x1	RW	D3 Hot function enable register (D3_HOT_FXN_EN) This bit is from pin input which is set 1. Software can alter it as needed. 0: D3 Hot Disabled 1: D3 Hot Enabled
30	0x0	RW	Allow L1 Core Clock Gating (ALL_L1_CORE_CG) When set to 1 allows core clock being gated during L1 state.
29	0x0	RW	Allow Engine PHY Status Extension (AL_EP_SEXT) When set to 1 allows the engine to extend PHY status of PCIe PIPE for one more cycle. This is due to the fact that our rate change function has a potential of not being able to sample the phystatus signal.
28	0x0	RW	Allow Engine PCIe Rate Change Passing (ALL_EP_RCP) When set to 1 allows the engine to pass PCIe rate change signal as it is from PCIe core to PCIe PHY.
27	0x0	RW	Allow Engine PERST Fundamental Reset (AL_PERST_FRST) When set to 1 allow engine to treat PERST# as a foundamental reset
26	0x0	RW	Overwrite PCIe P2 to P1 (OVR_PCIE_P2_P1) When set to 1 will overwrite a PCIe powerdown state of P2 to P1.
25	0x0	RW	Set Internal SSV 1 (SET_ISSV_1) When set to 1 set the internal SSV to 1.
24	0x0	RW	Clear Internal SSV 0 (CLR_ISSV_0) When set to 1 clear the internal SSV to 0.
23	0x1	RW	Enable Save/Restore Software Loading (EN_SRE_SW_LD) This is a bit that enables the save_restore_enable signal being loaded when a software command has set Save bit. This is a debug function.
22	0x0	RW	RESERVED (RSVD_1) RESERVED
21	0x0	RW	Force Save/Restore 1 (FORCE_SR1) When set to 1, it will force the save_restore flag to 1. This flag is an bit to ensure that the controller has masked the update during low power state. If software write this bit to 1, it must write it to 0 in order to resume the normal save and restore function.
20	0x0	RW	Disable Warm Reset Detect Speculative Upstream Ports (CFG_DIS_WRSTDET_SPECU) 0: Speculative upstream for Debug and SS/SSP port will detect WPR 1: No speculative upstream till port configuration is completed
19	0x0	RW	I/O Buffer Drive Strength (CIDS1) Controls the drive strength of the IO buffer
18	0x0	RW	I/O Buffer Drive Strength (CIDS0) Controls the drive strength of the IO buffer
17	0x0	RW	Disable Arc RXDP3 (CFG_DIS_ARC_RXDP3) When set to '1' DIsables arc to RXDET_p3 on disc from U2P3/U3
16	0x0	RW	cfg clk gate dis (CCGD) 1: Disable USB3 port clock gating 0: Enable USB3 port clock gating
15	0x1	RW	Enable CFG RXDET P3 (EN_CFG_RDP3) When set to '1' enable cfg rxdet p3
14	0x0	RW	Enable CFG PIPE Reset (EN_CFG_PIPE_RST) When set to '1' enable cfg pipe rst
13	0x1	RW	Enable Filter TX Idle (EN_FILT_TX_IDLE) When set to 1 enables a filter function to TX electrical idle signal at PCIe PIPE. The controller has a filter that sets TXelecidle signal of PCIe PIPE to 1 when it is in isolation state or power down transition states.
12	0x1	RW	Enable Host Engine Generate PME (EN_HE_GEN_PME) This is a global switch to whether or not eable this host engine to generate PME message.
11	0x1	RW	Enable Isolation (EN_ISOL) When set to '1' enable isolation
10	0x1	RW	Enable L1 Caused P2 Overwrite (EN_L1_P2_OVR) Set 1 to enable a new feature. This new feature is designed to use L1 as a state to identify whether the controller should do P2 Overwrite or not. Legacy behavior: P1 state was used to identify whether or not to invoke P2 overwrite function.
9	0x0	RW	Enable Core Clock Gating (EN_CORE_CG) When set to '1' disable core clock gating based on low power state entered
8	0x0	RW	Enable PHY Status Timeout (EN_PHY_STS_TO) When set to '1' enable PHY status timeout function which is designed to cover the PCIePHY issue that the controller may have not able to detect the PHY status toggle.
7	0x1	RW	Ignore aux_pm_en PCIe Core (IGN_APE_PC) When set to '1' ignore the aux_pm_en reg from PCIe core to continue the remote wake/clock switching support
6	0x1	RW	Enable P2 Overwrite P1 (EN_P2_OVR_P1) When set to '1' enable P2 overwrite P1 when PCIe core has indicated the transition from P0 to P1. This is to enable entering the even lower power state.
5	0x1	RW	Enable P2 Remote Wake (EN_P2_REM_WAKE) When set 1 '1' enable the remote wake function by allowing P2 clock/switching and P2 entering
4:1	0x0	RW	Forced PM State (FORCED_PM_STATE) Forced PM state
0	0x0	RW	Initiate Force PM State (INIT_FPMS) When set to '1' force PM state to go to the state indicated in bit 4:1