XHC Latency Tolerance Parameters LTV Control (XLTP_LTV1) – Offset 8174 - 1.3 - ID:764981 | 13th Generation Intel® Core™ Processor Datasheet, Volume 2 of 2

13th Generation Intel® Core™ Processor Datasheet, Volume 2 of 2

ID	Date	Version	Classification
764981	07/13/2023		Public

XHC Latency Tolerance Parameters LTV Control (XLTP_LTV1) – Offset 8174

XHC Latency Tolerance Parameters LTV Control

Bit Range	Default	Access	Field Name and Description
31	0x0	RW	Disable scheduler direct transition from IDLE to NO requirement (DIS_SDT_IDL_NR) 0: (default) allow scheduler direct transition from IDLE to NO requirement 1: Disable scheduler direct transition from IDLE to NO requirement
30	0x0	RW	XHCI LTR Transition Policy (XLTRTP) (LTR_TRANS_POL) When 0, the LTR messaging state machine transitions through High Med Low Active states assuming enough latency is available for each transition. When 1, LTR messaging state machine transitions from High, Medium, or Low LTR states to Active state upon the Alarm Timer timeout and stays in Active until the next service boundary.
29	0x0	RW	Include Scheduler First Round in Active Signal Disable (INCL_ROUND1_DIS) 0: xHC Engine Idle from the Power Scheduler will not assert if the Scheduler is performing its first round pass through periodic endpoints. 1: (Debug bit only) Revert to previous behavior. Scheduler's first round checks not included in xHC Engine Idle equation.
28	0x0	RW	XHCI LTR Active Enable (XLTRAE) (XLTRAE) 0: The Power Scheduler will not request an LTR message on a transition to ACTIVE. 1: The Power Scheduler will request an LTR message on a transition to ACTIVE.
27	0x0	RW	Power Scheduler Local Clock Gating Enable (PWRLCGE) (PWRLCGE) 0: Power Scheduler does not use local clock gating 1: Power Scheduler's local clock gating enabled. Note: This functionality is no longer required. This LCG existed previous to the inclusion of Aux clock gating.
26	0x0	RW	LTR EVM Hysteresis Max Count (LTR_HYS_MAX) Power Scheduler's Periodic IDLE residency before the controller asserts Periodic Complete. 0: Hysteresis set to 127 clock ticks. (.64us) 1: Hysteresis set to 31 clock ticks (.16us)
25	0x0	RW	Enable USB2 Port L0 LTV Based on Active Async (EN_USB2_LTV_U0_PORT_ASYNC_ACTIVE) 0: USB2 Port L0 LTV is used regardless of whether there is active async EPs being present or not (Legacy mode) 1: USB2 LTR L0 LTV is used only when there is active async EPs being present on that port. In the absence of active async EPs on given port, the L0 LTR value is NoRequirement for that port.
24	0x1	RW	XHCI LTR Enable (XLTRE) This bit must be set to enable LTV messaging from XHCI to the PMC.
23:12	0x400	RW	Periodic Active LTV (PA_LTV) 23:22 Latency Scale 00b: Reserved 01b: Latency Value to be multiplied by 1024 10b: Latency Value to be multiplied by 32,768 11b: Latency Value to be multiplied by 1,048,576 21:12 Latency Value (ns) Defaults to 0 micro seconds
11:0	0xC01	RW	USB2 Port L0 LTV (USB2_PL0_LTV) 11:10 Latency Scale 00b: Reserved 01b: Latency Value to be multiplied by 1024 10b: Latency Value to be multiplied by 32,768 11b: Latency Value to be multiplied by 1,048,576 9:0 Latency Value (ns) Defaults to 128 Micro Seconds