12th Generation Intel® Core™ Processors

Datasheet, Volume 1 of 2

ID 655258
Date 05/30/2022

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

LPDDR5 DC Specification

LPDDR5 Signal Group DC Specifications

Symbol

Parameter

H/P /U Processor Line

Units

Notes1

Minimum

Typical

Maximum

VIL

Input Low Voltage

- 0.15*Vdd2 0.06*Vdd2

V

2, 3, 4

VIH

Input High Voltage

0.24*Vdd2 0.15*Vdd2 -

V

2, 3, 4

RON_​UP(DQ)

Data Buffer pull-up Resistance

30 50

Ω

5,12

RON_​DN(DQ)

Data Buffer pull-down Resistance

30 50

RODT(DQ)

On-die termination equivalent resistance for data signals

30 240

Ω

6, 12

VODT(DC)

On-die termination DC working point (driver set to receive mode)

0 0.6*Vdd2

V

12

RON_​UP(CK)

Clock Buffer pull-up Resistance

30 50

Ω

5, 12

RON_​DN(CK)

Clock Buffer pull-down Resistance

30 50

Ω

5, 12

RON_​UP(CMD)

Command Buffer pull-up Resistance

30 50

Ω

5, 12

RON_​DN(CMD)

Command Buffer pull-down Resistance

30 50

Ω

5, 12

RON_​UP(CTL)

Control Buffer pull-up Resistance

30 50

Ω

5, 12

RON_​DN(CTL)

Control Buffer pull-down Resistance

30 50

Ω

5, 12

RON_​UP

(SM_​PG_​CNTL1)

System Memory Power Gate Control Buffer Pull-up Resistance

Ω

RON_​DN

(SM_​PG_​CNTL1)

System Memory Power Gate Control Buffer Pull- down Resistance

Ω

ILI

Input Leakage Current (DQ, CK)

0 V

0.2* VDD2

0.8* VDD2

mA

DDR0_​VREF_​DQ

DDR1_​VREF_​DQ

DDR_​VREF_​CA

VREF output voltage

NA NA NA

V

SM_​RCOMP[0]

Command COMP Resistance

99 100 101

Ω

SM_​RCOMP[1]

Data COMP Resistance

99 100 101

Ω

SM_​RCOMP[2]

ODT COMP Resistance

99 100 101

Ω

Notes:
  1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. Timing specifications only depend on the operating frequency of the memory channel and not the maximum rated frequency
  2. VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low value.
  3. VIH is defined as the minimum voltage level at a receiving agent that will be interpreted as a logical high value.
  4. VIH and VOH may experience excursions above VDD2. However, input signal drivers should comply with the signal quality specifications.
  5. Pull up/down resistance after compensation (assuming ±5% COMP inaccuracy). Note that BIOS power training may change these values significantly based on margin/power trade-off. Refer to processor I/O Buffer Models for I/V characteristics.
  6. ODT values after COMP (assuming ±5% inaccuracy). BIOS MRC can reduce ODT strength towards
  7. The minimum and maximum values for these signals are programmable by BIOS to one of the two sets.
  8. SM_​RCOMP[x] resistance should be provided on the system board with 1% resistors. SM_​RCOMP[x] resistors are to VSS. Values are pre-silicon estimations and are subject to change.
  9. SM_​DRAMPWROK must have a maximum of 15 ns rise or fall time over VDD2 * 0.30 ±100 mV and the edge must be monotonic.
  10. SM_​VREF is defined as VDD2/2 for DDR4
  11. RON tolerance is preliminary and might be subject to change.
  12. Maximum-minimum range is correct but center point is subject to change during MRC boot training.
  13. Processor may be damaged if VIH exceeds the maximum voltage for extended periods.