600 Series Chipset Family On-Package Platform Controller Hub

Datasheet, Volume 1 of 2

ID 691222
Date 01/05/2022

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

Signal Description

Signal Descriptions

Name

Type

Description

GPP_​D0 / ISH_​GP0 / BK0 / SBK0

OD

Blink BK 0: This function provides the blink (or PWM) capability. The blink/PWM frequency and duty cycle is programmable through the PWM Control register. Refer to Volume 2 for details.
GPP_​D1 / ISH_​GP1 / BK1 / SBK1

OD

Blink BK 1: This function provides the blink (or PWM) capability. The blink/PWM frequency and duty cycle is programmable through the PWM Control register. Refer to Volume 2 for details.
GPP_​D2 / ISH_​GP2 / BK2 / SBK2

OD

Blink BK 2: This function provides the blink (or PWM) capability. The blink/PWM frequency and duty cycle is programmable through the PWM Control register. Refer to Volume 2 for details.
GPP_​D4 / IMGCLKOUT0 / BK4 / SBK4

OD

Blink BK 4: This function provides the blink (or PWM) capability. The blink/PWM frequency and duty cycle is programmable through the PWM Control register. Refer to Volume 2 for details.
GPP_​E22 / DDPA_​CTRLCLK / DNX_​FORCE_​RELOAD

I

Download and Execute (DnX):Intel® CSME ROM samples this pin any time ROM begins execution. This includes the following conditions:

  • G3 Exit.
  • Sx, Moff Exit.
  • Cold Reset(Host Reset with Power Cycle) Exit.
  • Warm Reset(Host Reset without Power Cycle) Exit if Intel® CSME was shutdown in Warm Reset.
  • 0 => No DnX; 1=> Enter DnX mode Note:This pin must not be sampled high at the sampling time for normal operation.

GPP_​E0 / SATAXPCIE0 / SATAGP0

I

SATA port 0 or PCIe port mux select : This is used to select SATA/PCIe function to support implementations like SATA Express or mSATA.
GPP_​A12 / SATAXPCIE1 / SATAGP1

I

SATA port 1 or PCIe port mux select : This is used to select SATA/PCIe function to support implementations like SATA Express or mSATA.
GPP_​D0 / ISH_​GP0 / BK0 / SBK0

OD

Serial Blink SBK 0: This function provides the capability to serialize POST or other messages on the pin to a serial monitor. The Serial Blink message is programmed through the Serial Blink Command/Status and Serial Blink Data registers. Refer to Volume 2 for details.
GPP_​D1 / ISH_​GP1 / BK1 / SBK1

OD

Serial Blink SBK 1: This function provides the capability to serialize POST or other messages on the pin to a serial monitor. The Serial Blink message is programmed through the Serial Blink Command/Status and Serial Blink Data registers. Refer to Volume 2 for details.
GPP_​D2 / ISH_​GP2 / BK2 / SBK2

OD

Serial Blink SBK 2: This function provides the capability to serialize POST or other messages on the pin to a serial monitor. The Serial Blink message is programmed through the Serial Blink Command/Status and Serial Blink Data registers. Refer to Volume 2 for details.
GPP_​D4 / IMGCLKOUT0 / BK4 / SBK4

OD

Serial Blink SBK 4: This function provides the capability to serialize POST or other messages on the pin to a serial monitor. The Serial Blink message is programmed through the Serial Blink Command/Status and Serial Blink Data registers. Refer to Volume 2 for details.
GPP_​B15 / TIME_​SYNC0 / ISH_​GP7 I Time Synchronization GPIO 0: Timed GPIO event for time synchronization for interfaces that do not support time synchronization natively.
GPP_​F9 / BOOTMPC O Boot Media Power Control: If BOOTMPC is 0 - Powered Off.

If BOOTMPC is 1 - Powered On.