Intel® Core™ Ultra 200H and 200U Series Processors

Datasheet, Volume 1 of 2

ID Date Version Classification
842704 05/27/2025 Public
Document Table of Contents

Signal Description

Signal Name

Type

Description

Availability

USB32_​1_​RXN

USB32_​1_​RXP

I

USB 3.2 Differential Receive Pair 1: These are USB 3.2-based high-speed differential signals for Port 1. The signal should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB32_​1_​TXN

USB32_​1_​TXP

O

USB 3.2 Differential Transmit Pair 1: These are USB 3.2-based high-speed differential signals for Port 1. The signal should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB32_​2_​RXN

USB32_​2_​RXP

I

USB 3.2 Differential Receive Pair 2: These are USB 3.2-based high-speed differential signals for Port 2. The signal should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB32_​2_​TXN

USB32_​2_​TXP

O

USB 3.2 Differential Transmit Pair 2: These are USB 3.2-based high-speed differential signals for Port 2. The signal should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​1

USB2N_​1

I/O

USB 2.0 Port 1 Transmit/Receive Differential Pair 1: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​2

USB2N_​2

I/O

USB 2.0 Port 2 Transmit/Receive Differential Pair 2: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​3

USB2N_​3

I/O

USB 2.0 Port 3Transmit/Receive Differential Pair 3: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​4

USB2N_​4

I/O

USB 2.0 Port 4 Transmit/Receive Differential Pair 4: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​5

USB2N_​5

I/O

USB 2.0 Port 5 Transmit/Receive Differential Pair 5: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​6

USB2N_​6

I/O

USB 2.0 Port 6 Transmit/Receive Differential Pair 6: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​7

USB2N_​7

I/O

USB 2.0 Port 7 Transmit/Receive Differential Pair 7: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​8

USB2N_​8

I/O

USB 2.0 Port 8 Transmit/Receive Differential Pair 8: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​9

USB2N_​9

I/O

USB 2.0 Port 9 Transmit/Receive Differential Pair 9: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

USB2P_​10

USB2N_​10

I/O

USB 2.0 Port 10 Transmit/Receive Differential Pair 10: This USB 2.0 signal pair are routed to xHCI controller and should be mapped to a USB connector with one of the OC (overcurrent) signals.

H/U-Series Processor

GPP_​E09/USB_​OC0#/USB-C_​GPP_​E09

I

Overcurrent Indicators: This signal set the corresponding bit in the xHCI controller to indicate that an overcurrent condition has occurred.

When configured as OC# pin, a 10 kohm pull-up resistor is required to be connected to the power-rail. When this pin is configured as GPIO, no pull-up resistor is required.

Notes:

  1. OC# pins are not 5 V tolerant.
  2. OC# pins can be shared between USB ports.
  3. Each USB connector should only have one OC# pin protection.

H/U-Series Processor

GPP_​B11/USB_​OC1#/DDSP_​HPD2/DISP_​MISC3/USB-C_​GPP_​B11

I

Overcurrent Indicators: This signal set the corresponding bit in the xHCI controller to indicate that an overcurrent condition has occurred.

When configured as OC# pin, a 10 kohm pull-up resistor is required to be connected to the power-rail. When this pin is configured as GPIO, no pull-up resistor is required.

Notes:

  1. OC# pins are not 5 V tolerant.
  2. OC# pins can be shared between USB ports.
  3. Each USB connector should only have one OC# pin protection.

H/U-Series Processor

GPP_​B14/USB_​OC2#/DDSP_​HPD3/DISP_​MISC4/USB-C_​GPP_​B14

I

Overcurrent Indicators: This signal set the corresponding bit in the xHCI controller to indicate that an overcurrent condition has occurred.

When configured as OC# pin, a 100 kohm pull-up resistor is required to be connected to the power-rail.

When this pin is configured as GPIO, no pull-up resistor is required.

Notes:

  1. OC# pins are not 5 V tolerant.
  2. OC# pins can be shared between USB ports.
  3. Each USB connector should only have one OC# pin protection.

H/U-Series Processor

GPP_​B15/USB_​OC3#/USB-C_​GPP_​B15

I

Overcurrent Indicators: This signal set the corresponding bit in the xHCI controller to indicate that an overcurrent condition has occurred.

When configured as OC# pin, a 10 kohm pull-up resistor is required to be connected to the power-rail. When this pin is configured as GPIO, no pull-up resistor is required.

Notes:

  1. OC# pins are not 5 V tolerant.
  2. OC# pins can be shared between USB ports.
  3. Each USB connector should only have one OC# pin protection.

H/U-Series Processor

USB2_​1_​RCOMP

A

USB Resistor Bias, analog connection points for an external resistor 200 ohm ± 1% connected to GND.

H/U-Series Processor

USB2_​2_​RCOMP

A

USB Resistor Bias, analog connection points for an external resistor 200 ohm ± 1% connected to GND.

H/U-Series Processor

USB32_​RCOMP

A

USB Resistor Bias, analog connection points for an external resistor 200 ohm ± 1% connected to GND.

H/U-Series Processor